Recent Posts

Pages: [1] 2 3 ... 10
1
BreakawayOne / Re: Voice vs Music Issue
« Last post by JesseG on December 16, 2017, 05:08:04 AM »
Can you share a snippet of the voice/s in question that you're experiencing distortion with (preferably ~30 sec wav), and also the preset that you're using?
2
Breakaway Audio Enhancer / Re: Windows 10 crash on registering application
« Last post by JesseG on December 16, 2017, 04:42:19 AM »
You should try installing the latest version of Breakaway Audio Enhancer from here:
http://www.claessonedwards.com/download/breakaway_setup_1.40.03.exe
which was updated to work with Windows 10
3
Breakaway Professional Products / Re: Enhancing live vocals
« Last post by JesseG on December 16, 2017, 04:35:35 AM »
AlexDrop, it depends on what the other products you're comparing it to actually do, and what "these type of things" means.

As a general purpose final broadcast audio processor, BreakawayOne competes squarely with all of the other flagship processors from the major manufacturers, as well as basically being the nephew of the Omnia.9 one of Omnia's two flagships. Some will say it's better or worse than whatever other brand's flagship processor (some of them cost over $10,000 btw, most are over $7,000), which is a never-ending debate, but ~everyone can agree that it's a competently and properly engineered piece of broadcast equipment. Leif's processing has been used on everything from the Super Bowl (the last 14x actually) to the Olympics (they use 75-100 boxes), and have been installed everywhere from the Eiffel Tower to Voice Of America.

TLDR; Yes. :P
4
BreakawayOne / Voice vs Music Issue
« Last post by Big Mix Radio on December 10, 2017, 10:40:01 PM »
I am hoping to find a solution to the issues I am having =-) Ok, I use Station Playlist to stream. When I play music, everything sounds really good, at pretty much any level going into BreakawayOne. Now when I do voice tracking , not so much. However, listening from Station Playlist directly to the Audient ID 22. All audio plays fine with no distortion artifacts. Now when I switch the audio path to BreakawayOne via the Virtual Audio Cables, only the voice tracks sounds distorted. I say distorted because the audio is not clipping. When looking at voice tracks in adobe audition they are not clipped in any way. I do not process the voice track in any way. No compression, limiting are used.  I have tried a variety of different ideas, for example , routing the output of Adobe Audition through VAC to BreakawayOne to see if the issues is still there. And unfortunately I get the same results, with voice only, even if I record the audio, peaking at -24dbfs in Adobe. The only thing doing it this way was the increased noise floor, which I expected to see as the rercording level was too low I did not have the issue when I used Breakaway Live for some reason, at least I did not notice it. Of course that was on a XP computer. Now Windows 10, which I am not a fan of. So I am curious if anyone has an idea as to what may be going on.

What I use:
Windows 10 Pro
Audient ID22
Shure SM7B

Thanks,
Thomas

5
Breakaway Professional Products / Re: Enhancing live vocals
« Last post by AlexDop on December 07, 2017, 02:38:45 PM »
How close is BreakawayOne to other professional software for these type of things?
6
Breakaway Audio Enhancer / Re: Unable to open "Breakaway pipeline 1"?
« Last post by flagg on December 04, 2017, 10:17:06 AM »
I have now also tested this on a Scarlet 2i2, with the same issue on Windows 7. "Device does not support requested format or sound device is busy". Yes these cards are set to 48000. I really wish this problem could be fixed, life isn't the same without Breakaway. I tried DFX and it's not even close to the quality.
7
Breakaway Audio Enhancer / Re: Windows 10 crash on registering application
« Last post by Snabel on December 03, 2017, 06:02:42 AM »
I wish I could throw money at this proble, but it would do nothing so I'm without options.
I'm just trying to register the software I bought.
8
BreakawayOne / Re: Breakaway DJ to Breakaway one
« Last post by JesseG on December 01, 2017, 11:53:34 PM »
BreakawayOne technically can't replace Breakaway DJ, if you were/are using Breakaway DJ's virtual ASIO driver to sit between your music software and your actual soundcard's ASIO.

But... you can install ASIO4ALL virtual ASIO to Kernel Streaming interface... which can work with the Breakaway Pipeline virtual soundcards, to route audio from your music software's ASIO output, into BreakawayOne via Kernel Streaming, and then you would use BreakawayOne to output to your actual soundcard with ASIO. Which other than a little bit of added latency, will accomplish what you want to do.



That being said... I haven't found a situation yet where the results aren't more consistent and listenable by just processing the mix after the master output of the DJ mixer. If you are willing to test that method, just using the ASIO drivers of your mixer or soundcard... I think you'll agree. Not only does that require only 1x HD + 1x Low-latency in the license for it, but you'll be able to get even lower latency than you could have achieved with Breakaway DJ. (most likely somewhere between 25-50% less latency)

That, combined with how few copies of Breakaway DJ were sold (it's not even a 3-digit number), made it fairly easy to decide not to do the large amount of work required to give a 100% all-uses all-functionality upgrade path (vs 99.9%) for a very small group of customers.
9
BreakawayOne / Re: Breakaway DJ to Breakaway one
« Last post by ColinW62 on November 30, 2017, 09:51:01 PM »
Hi Milky

I'm struggling to follow this.  Like Chilly I'm trying to get BA One working like BA DJ, ie process 2 stereo outputs independently that will appear on 2 faders on the mixer/DJ Controller.  I think BA DJ achieved this through being 2 BA processors in one. 

If I understand BA One correctly it can be set up to process 2 outputs independently - ie 2 different radio stations.  So I'm guessing it can be set up to process the 2 outputs from the controller in a similar way.  Is this what you have done with BA One?  If so can you help please with a simpler step by step?

Colin
10
BreakawayOne / Re: Breakaway DJ to Breakaway one
« Last post by MixMaker on November 21, 2017, 10:19:16 PM »
So, to setup two "cores" to use BAONE as BADJ I need to purchase HD two times?
Pages: [1] 2 3 ... 10